Short answer: a single-wide typically costs $3,000–$9,000 to move within 50 miles ($6,000–$17,000 for full-service relocation including utility work and site setup). A double-wide runs $5,000–$15,000+ for full-service relocation, since it has to be split into two pieces to transport.
Those ranges assume transport only versus a complete relocation package, because hauling the unit is just one line item in a longer checklist that includes disconnection, site prep, and final anchoring. A transport-only quote covers the truck, driver, and fuel for the oversize load, while full-service pricing folds in capping water lines, leveling the new lot, and fastening the home to its foundation. If you are comparing bids, ask whether each quote includes setup or just the haul, since mixing the two categories makes the price gap look larger than it really is.
This isn't a household move — it's structural transport
A full-service household move relocates your belongings. Moving a mobile home relocates the structure itself, which is a fundamentally different job: an oversize-load permit, often a pilot or escort vehicle depending on width and state rules, a specialized hauler rated for the home's weight and dimensions, and utility disconnection at the origin plus site preparation and reconnection at the destination.
A household moving truck stays within standard lane widths and weight limits, but a mobile home exceeds both, which triggers state-by-state routing rules that may force detours onto wider roads or restrict travel to daylight hours. Haulers sometimes have to coordinate with utility crews to raise power lines or navigate around low overpasses, tasks that simply do not exist when a van line carries boxes from one apartment to another.
The transporter is not a standard freight operator; it is a contractor with lowboy trailers, hydraulic jacks, and tie-down systems rated specifically for manufactured housing rather than general cargo. If the home’s roofline sits too high, the company may also remove fixtures temporarily or select a route with greater overhead clearances, adding planning hours that a conventional move rarely requires.
Homeowners sometimes assume utility disconnection is a quick phone call, yet it can involve capping sewer lines, removing meter pedestals, and securing loose siding before the structure rolls, each step requiring either separate trades or the mover’s setup crew. Skipping any of these preparatory tasks can delay the haul or damage the home when it flexes over road bumps, which is why full-service quotes exist to keep every stage on one coordinated timeline.
Why does a double-wide cost more to move than a single-wide?
A single-wide moves as one unit, which keeps the job comparatively simpler. A double-wide (or triple-wide) was manufactured and delivered as separate sections joined together on-site — moving it means reversing that process: splitting the halves apart, transporting each on its own truck, then rejoining and resealing them at the new location. That extra step is the main reason double-wide relocations cost meaningfully more.
Rejoining the halves is not just pushing two units together; the crew must realign the marriage line precisely so floors, walls, and roofs meet without gaps that let in moisture or compromise insulation. After alignment, they seal the exterior seams and often patch or replace the longitudinal trim pieces that were removed for transport, labor that adds hours beyond the driving time.
Because each half travels on its own flatbed, a double-wide move ties up two trucks, two drivers, and significantly more fuel than a comparable single-wide trip, which is why transport-only pricing still jumps sharply even before setup costs enter the picture. Scheduling both halves to arrive on the same day keeps the crane or assembly crew on site for a single block of time, whereas staggered deliveries can idle labor and extend the overall project.
A triple-wide follows the same principle with three sections, multiplying the coordination required for alignment and sealing at the destination. Once the home has been lived in, the marriage lines may have settled slightly, so the crew sometimes has to shim or level one section before the other can lock into place, a correction that factory delivery crews rarely face when the units are brand new.
What permits and inspections are required to move a mobile home?
Every state and often every county has its own permit requirements for transporting a mobile home, typically running $100 to $2,000+, and some jurisdictions require inspections at both the pickup and destination sites. An experienced mobile home moving company usually handles this paperwork as part of the quoted price — worth confirming upfront rather than discovering it's on you.
Rural counties often charge toward the lower end of the $100 to $2,000+ spectrum, while dense urban jurisdictions may layer highway-department permits, police escort approvals, and bridge-crossing reviews on top of one another. That stack of applications explains why the permit line item can sit at the high end of the range even when the haul distance is relatively short.
Inspections are not just paperwork checks; an inspector may verify that the home still meets transport bracing standards or that the destination lot has approved setbacks and utility trenches before the truck arrives. Failing either inspection can halt the move until corrections are made, so experienced movers often walk the site beforehand to spot red flags rather than risk a failed stop.
A quote that says permits included generally means the mover pays the state and county fees directly, but it does not always cover third-party inspections or utility-release sign-offs that some jurisdictions require from the homeowner. Ask for a written breakdown of which permits are bundled and which ones might show up as separate invoices, so the $100 to $2,000+ range does not surprise you mid-project.
If the planned route crosses tribal land, military bases, or toll bridges with width restrictions, additional approvals outside standard state permits may enter the timeline. Haulers who work the same region repeatedly usually keep a checklist of these edge cases, which is one reason hiring a specialist matters more than simply finding the cheapest per-mile rate.
What drives mobile home moving costs besides size?
- Distance — same as any move, but permit and escort requirements can compound this more than a standard household shipment.
- Age and condition — older homes sometimes need additional bracing or reinforcement to survive the move safely.
- Site prep at the destination — foundation, utility hookups, and skirting work are typically quoted separately from transport.
Distance matters for any move, but oversize-load rules compound the cost because some states mandate rest stops at certified weigh stations or limit travel to daylight hours, stretching a long haul across multiple days instead of one. Each extra day adds driver wages, possible crew lodging, and escort-vehicle retainers that would not appear on a standard household shipment covering the same mileage.
Older homes may have dry-rotted subfloors, rusted tie-down frames, or brittle roof flashing that cannot withstand the vibration of highway speeds without extra bracing. A mover will often send an inspector to photograph the undercarriage and note any tears in the belly wrap, because discovering structural weakness after the home is already on the highway can force an unplanned offload and repair stop.
Foundation and utility work are typically quoted separately from transport for a reason: the new lot may need grading, a poured pad, or pier installation before the first half arrives. Skirting replacement is another frequent post-move expense, since the original panels are rarely designed to survive removal and reattachment, meaning the setup budget extends well beyond the day the truck pulls away.
Homeowners sometimes forget that trees, fences, or outbuildings on the new lot must be cleared to create an access path wide enough for a flatbed and any crane or equipment needed to place the home. If the site prep quote assumes an open field but the reality is a narrow driveway with low branches, the transport crew may arrive and find the home cannot be backed into position, triggering expensive last-minute tree service or a return trip.